135 lines
4.9 KiB
C
135 lines
4.9 KiB
C
/* @(#)clock.h 1.1 92/07/30 SMI */
|
|
|
|
/*
|
|
* Copyright (c) 1985 by Sun Microsystems, Inc.
|
|
*/
|
|
|
|
/*
|
|
* Definitions for the Intersil 7170 real-time clock. This chip
|
|
* is used as the timer chip in addition to being the battery
|
|
* backed up time-of-day device. This clock is run by UNIX in
|
|
* the 100 hz periodic mode giving interrupts 100 times/second.
|
|
* The low level code dismisses every other interrupt, thus
|
|
* creating an effective 50 hz rate for hardclock().
|
|
*
|
|
* Reading clk_hsec latches the the time in all the other bytes
|
|
* so you get a consistent value. To see any byte change, you
|
|
* have to read clk_hsec in between (e.g. you can't loop waiting
|
|
* for clk_sec to reach a certain value without reading clk_hsec
|
|
* each time).
|
|
*/
|
|
|
|
#ifndef _sun3_clock_h
|
|
#define _sun3_clock_h
|
|
|
|
#define SECDAY ((unsigned)(24*60*60)) /* seconds per day */
|
|
#define SECYR ((unsigned)(365*SECDAY)) /* seconds per common year */
|
|
|
|
/*
|
|
* The 7170 uses year % 4 to figure out if
|
|
* we have a leap year, we do the same here.
|
|
*/
|
|
#define SECYEAR(yr) ((((unsigned)(yr) % 4) == 0)? SECYR + SECDAY : SECYR)
|
|
|
|
/*
|
|
* The year register counts from 0 to 99.
|
|
* Unix time is the number of seconds
|
|
* since the year YRREF. The 2 digit year
|
|
* value stored in the chip represents the
|
|
* the number of years beyond YRBASE.
|
|
* Note that YRBASE must be < YRREF and
|
|
* (YRBASE % 4) == 0 to do leap years correct.
|
|
* Note that we can only keep time up to the year 2068.
|
|
*/
|
|
#define YRREF 70 /* 1970 - where UNIX time begins */
|
|
#define YRBASE 68 /* 1968 - what year 0 in chip represents */
|
|
|
|
#define OBIO_CLKADDR 0x60000 /* address of clock in obio space */
|
|
|
|
#ifdef LOCORE
|
|
#define CLKADDR 0x0FFE2000 /* virtual address we map clock to be at */
|
|
#else
|
|
struct intersil7170 {
|
|
u_char clk_hsec; /* counter - hundredths of seconds 0-99 */
|
|
u_char clk_hour; /* counter - hours 0-23 (24hr) 1-12 (12hr) */
|
|
u_char clk_min; /* counter - minutes 0-59 */
|
|
u_char clk_sec; /* counter - seconds 0-59 */
|
|
u_char clk_mon; /* counter - month 1-12 */
|
|
u_char clk_day; /* counter - day 1-31 */
|
|
u_char clk_year; /* counter - year 0-99 */
|
|
u_char clk_weekday; /* counter - week day 0-6 */
|
|
u_char clk_rhsec; /* RAM - hundredths of seconds 0-99 */
|
|
u_char clk_rhour; /* RAM - hours 0-23 (24hr) 1-12 (12hr) */
|
|
u_char clk_rmin; /* RAM - minutes 0-59 */
|
|
u_char clk_rsec; /* RAM - seconds 0-59 */
|
|
u_char clk_rmon; /* RAM - month 1-12 */
|
|
u_char clk_rday; /* RAM - day 1-31 */
|
|
u_char clk_ryear; /* RAM - year 0-99 */
|
|
u_char clk_rweekday; /* RAM - week day 0-6 */
|
|
u_char clk_intrreg; /* interrupt status and mask register */
|
|
u_char clk_cmd; /* command register */
|
|
u_char clk_unused[14];
|
|
};
|
|
#define CLKADDR ((struct intersil7170 *)(0x0FFE2000))
|
|
#endif
|
|
|
|
/* offsets into structure */
|
|
#define CLK_HSEC 0
|
|
#define CLK_HOUR 1
|
|
#define CLK_MIN 2
|
|
#define CLK_SEC 3
|
|
#define CLK_MON 4
|
|
#define CLK_DAY 5
|
|
#define CLK_YEAR 6
|
|
#define CLK_WEEKDAY 7
|
|
#define CLK_RHSEC 8
|
|
#define CLK_RHOUR 9
|
|
#define CLK_RMIN 10
|
|
#define CLK_RSEC 11
|
|
#define CLK_RMON 12
|
|
#define CLK_RDAY 13
|
|
#define CLK_RYEAR 14
|
|
#define CLK_RWEEKDAY 15
|
|
#define CLK_INTRREG 16
|
|
#define CLK_CMD 17
|
|
|
|
/*
|
|
* In `alarm' mode the 7170 interrupts when the current
|
|
* counter matches the RAM values. However, if the ignore
|
|
* bit is on in the RAM counter, that register is not
|
|
* used in the comparision. Unfortunately, the clk_rhour
|
|
* register uses a different mask bit (because of 12 hour
|
|
* mode) and thus the 2 different defines.
|
|
*/
|
|
#define CLK_IGNORE 0x80 /* rmsec, rmin, rsec, rmon, rday, ryear, rdow */
|
|
#define CLK_HOUR_IGNORE 0x40 /* ignore bit for clk_rhour only */
|
|
|
|
/*
|
|
* Interrupt status and mask register defines,
|
|
* reading this register tells what caused an interrupt
|
|
* and then clears the state. These can occur
|
|
* concurrently including te RAM compare interrupts.
|
|
*/
|
|
#define CLK_INT_INTR 0x80 /* r/o pending interrrupt */
|
|
#define CLK_INT_DAY 0x40 /* r/w periodic day interrupt */
|
|
#define CLK_INT_HOUR 0x20 /* r/w periodic hour interrupt */
|
|
#define CLK_INT_MIN 0x10 /* r/w periodic minute interrupt */
|
|
#define CLK_INT_SEC 0x08 /* r/w periodic second interrupt */
|
|
#define CLK_INT_TSEC 0x04 /* r/w periodic 1/10 second interrupt */
|
|
#define CLK_INT_HSEC 0x02 /* r/w periodic 1/100 second interrupt */
|
|
#define CLK_INT_ALARM 0x01 /* r/w alarm mode - interrupt on time match */
|
|
|
|
/* Command register defines */
|
|
#define CLK_CMD_TEST 0x20 /* w/o test mode (vs. normal mode) */
|
|
#define CLK_CMD_INTRENA 0x10 /* w/o interrupt enable (vs. disabled) */
|
|
#define CLK_CMD_RUN 0x08 /* w/o run bit (vs. stop) */
|
|
#define CLK_CMD_24FMT 0x04 /* w/o 24 hour format (vs. 12 hour format) */
|
|
#define CLK_CMD_F4M 0x03 /* w/o using 4.194304MHz crystal frequency */
|
|
#define CLK_CMD_F2M 0x02 /* w/o using 2.097152MHz crystal frequency */
|
|
#define CLK_CMD_F1M 0x01 /* w/o using 1.048576MHz crystal frequency */
|
|
#define CLK_CMD_F32K 0x00 /* w/o using 32.768KHz crystal frequency */
|
|
|
|
#define CLK_CMD_NORMAL (CLK_CMD_INTRENA|CLK_CMD_RUN|CLK_CMD_24FMT|CLK_CMD_F32K)
|
|
|
|
#endif /*!_sun3_clock_h*/
|