Changelog: w11a_V0.74 -> HEAD

HEAD

General Proviso

The HEAD version shows the current development. No guarantees that software or firmware builds or that the documentation is consistent. The full set of tests is only run for tagged releases.

Special Provisos

DEUNA still with very limited functionality and testing
- no buffer chaining
- no loopback
- no memory access error checking
- works with 211bsd, ping and telnet login tested
DEUNA and nexys3 shows rlink aborts
- unlikely that it's a DEUNA issue
- more likely this revealed a hidden flaw in the fx2 based transport
- all works fine with nexys4 !

Summary

refurbish dmcmon
- has now the sta,sto,sus,res logic as rbmon and ibmon
- does not depend on full state number generation anymore
- missed WAIT instructions so far, has been fixed
dmcmon included in sys_w11a_n4 again
- full snum generation code gives bad synthesis under vivado (fine in ISE)
- the updated dmcmon can life with a simple, category based, snum
integrate rbus monitor in w11 shell
- ti_rri: setup rbus monitor if detected
- rw11/shell.tcl: add .rme,.rmd,.rmf,.rml
- ibd_ibmon/util.tcl: move out imap_reg2addr
- rbmoni/util.tcl: add procs filter,rme,rmf
- rlink/util.tcl: add amap_reg2addr
- rw11/util.tcl: move in imap_reg2addr; add imap_range2addr
- rw11/shell.tcl: integrate rbmon: add .rme,.rmd,.rmf,.rml
make setup procs idempotent
- RlinkConnect: add rbus monitor probe, add HasRbmon()
- RtclRlinkConnect: M_amap: -testname opt addr check; add hasrbmon get
- RtclRw11Cpu: M_(imap|rmap): -testname optional addr check
- */util.tcl: setup: now idempotent
w11 shell .bs now support ibus register names and ranges
- rw11/dmhbpt.tcl: hb_set: use imap_range2addr, allow regnam and range
add DEUNA (ethernet) support
- add DEUNA device (xu) for ibus
- add DEUNA to all sys_w11a systems
  - add ibdr_deuna to maxisys
  - setup sys_conf for all systems
- backend support classes for networking
  - RethBuf: ethernet buffer
  - RethTools: some handy tools
  - Rw11VirtEth: new virt base for ethernet
  - Rw11VirtEthTap: concrete networking via tap devices
- backend for DEUNA
  - Rw11CntlDEUNA: controller and almost all logic
  - Rw11UnitDEUNA: unit
- tcl support for DEUNA
- tbench support for DEUNA
- some new preinit and preboot hooks
factor out controller class specifics; add useful M_default output
- RtclRw11Cntl*Base: add classes with Rdma,Disk,Stream.Tape,Term specifics
- RtclRw11Cntl*: add class in ctor; derive from RtclRw11Cntl*Base
make list cpus,cntls,units command gettable; make controller class gettable
- RtclRw11: add CpuCommands() and cpus getter
- RtclRw11Cntl: add UnitCommands() and uints and class getter
- RtclRw11Cpu: add ControllerCommands() and cntls getter
- RtclGet: add Tcl_Obj* getter
make attach status and attach url gettable for units
- Rw11Cntl,Rw11CntlBase: NUnit() now pure; add UnitBase()
- Rw11Unit: add IsAttached(), AttachUrl()
- Rw11UnitVirt: add VirtBase()
- Rw11Virt: add Url() const getter
- RtclRw11UnitBase: add attached,attachutl getters
ensure that defaulted scheme visible in displayed open urls
- pass default scheme to RparseUrl in Open()
- add Open() overloads for Rw11VirtDiskFile and Rw11VirtDiskOver
- RparseUrl: add Set() with default scheme handling
revise interface for ibd_ibmon and rbd_rbmon
- use start,stop,suspend,resume functions; improved stop on wrap handling
- add 'repeat collapse' logic (store only first and last of a sequence)
BUGFIX: rlc get logfile or rlc get * crashed with segfault
- error was a type mismatch in the getter declaration in RtclRlinkConnect
- fixed by changing the return type in RlinkConnect
remove double inheritance in RtclRw11Unit* stack
- RtclRw11Unit: drop fpCpu, use added Cpu()=0 instead
- RtclRw11UnitBase: add TUV,TB; add TUV* ObjUV(); inherit from TB
- RtclRw11Unit(Disk|Stream|Tape|Term): define ObjUV();inherit from RtclRw11Unit
- RtclRw11Unit(dev): inherit from RtclRw11UnitBase
trace output with controller name
- Rw11Cntl*: use controller name as message prefix
more compact dumps, add Dump(..,detail)
- RlinkCommand: add CommandInfo()
- RtclCmdBase: add GetArgsDump()
- RlinkCommandList: Dump(): add detail arg
- Rstats: add NameMaxLength(); Print(): add counter name
- Rw11Cntl: use Dump(detail) for PrimClist ect
- Rw11(Cntl|Unit|Virt)*,: Dump(): add detail arg
- many other classes: Dump(): add detail arg
- RtclRw11(Cntl|Unit|*): M_dump: use GetArgsDump and Dump detail
RtimerFd: first practical version
use clock_gettime instead of gettimeofday
add Rw11VirtDiskOver (simple overlay file container)
- Rw11VirtDiskBuffer: added, disk buffer representation
- Rw11VirtDiskOver: added, a 'keep changes in memory' overlay file container
- Rw11Virt: add fWProt,WProt()
- Rw11VirtDiskFile: adopt WProt handling
- RtclRw11Unit: add fpVirt,DetachCleanup(),AttachDone(),M_virt()
- RtclRw11UnitBase: add AttachDone()
tcl command handling update
- support now sub-command handling
- support dynamically created commands (like 'virt')
- support command info (via '?' option)
move to Ubuntu 16.04 as development platform
- document urjtag build (jtag in Ubuntu 16.04 is broken)
- add environment sanity wrappers for acroread,awk,firefox to ensure proper operation of vivado under Ubuntu 16.04
use Rtime; drop Rtools::TimeOfDayAsDouble()
probe/setup auxilliary devices: kw11l,kw11p,iist
librw11/Rw11Cpu: add ModLalh()
librtools/Rstats: add IncLogHist() and fix + and * operator definition
add Rtime support in RtclGet/RtclSet
add librtools/Rtime: class for absolute and delta times
use -std=c++11 (gcc 4.7 or later)
update probe handling: add probe data, make it tcl getable
23 line interrupt mapper for full system configuration
man pages now available online.
add sysmon_rbus in sys_tst_sram_n4
Auto-dection of Digilent boards with FT2232HQ interface for ti_rri and ti_w11.

2017-01-07: w11a_V0.742 - rev 841(wfjm)

Summary

fixes for Vivado 2016.4; all designs build under vivado 2016.4
added preliminary support for Nexys4 DDR board (thanks to Michael Lyle for testing!)
w11 shell re-organized and expanded, now default in ti_w11
CPUERR cleared with cpu reset (see ECO-029)
PS initialized now with 000000 (see ECO-028)

2016-12-23: w11a_V0.741 - rev 826(wfjm)

Summary

moved w11 repository from OpenCores to GitHub wfjm/w11
moved w11 project pages from OpenCores to GitHub-Pages wfjm.github.io/home/w11
converted existing documentation from plain text to markdown
added README.md files in sub-directories

7.7 KiB Raw Blame History

Changelog: w11a_V0.74 -> HEAD

Table of contents

HEAD

General Proviso

Special Provisos

Summary

2017-01-07: w11a_V0.742 - rev 841(wfjm)

Summary

2016-12-23: w11a_V0.741 - rev 826(wfjm)

Summary

7.7 KiB

Raw Blame History