Merge pull request #9 from hlovdal/make-board001-subdirectory

Make board001 subdirectory

Electrical/Board_001/README.md

@@ -0,0 +1,45 @@
+# Electrical Design
+
+## Explained
+The design is using an opamp as a compined level converter and a schmitt trigger, in order to convert 
+the HAN signal into a 3.3V compatible serial format. As the input levels on the opamp is much higher 
+than our 5V supply, we are rectifying and smoothing the HAN signal to use for a supply here. (VDD)
+
+As a power source, we've used a micro USB connector, providing 5V, just as this is cheap and easy. However,
+no part of the circuit will need any other power than the 3.3V, so any combination of power source and 
+regulator that provides the 3.3V will do.
+
+The ESP8266 setup is a rather standaraized setup and will allow for programming the ESP directly on the 
+board, if needed. During programming, it might be neccessary to disconnect the incoming HAN.
+
+### **!!important changes!!**
+> * R8 should not be used
+> * The two unused inputs on the LM358 should be grounded (Pin 5 and 6)
+
+## Schematics
+![Schematics](./Schematics.PNG)
+
+## PCB
+![PCB](./PCB.PNG)
+
+## Componenet list
+Name | Value | Part
+-----|------|-----
+C1|10uF/25V|[P5148-ND](https://www.digikey.no/product-detail/en/panasonic-electronic-components/ECA-1EM100/P5148-ND/245007)
+C2|100nF|[BC1101CT-ND](https://www.digikey.no/product-detail/en/vishay-bc-components/K104K10X7RF5UH5/BC2665CT-ND/2356879)
+C3|220uF/35V|[1572-1706-ND](https://www.digikey.no/product-detail/en/illinois-capacitor/227CKS035M/1572-1706-ND/5411729)
+D1|1N4148|[1N4148FS-ND](https://www.digikey.no/product-detail/en/fairchild-on-semiconductor/1N4148/1N4148FS-ND/458603)
+P1||[609-4613-1-ND](https://www.digikey.no/product-detail/en/amphenol-fci/10118192-0001LF/609-4613-1-ND/2785378)
+P2|Female|[S7004-ND](https://www.digikey.no/product-detail/en/sullins-connector-solutions/PPTC061LFBN-RC/S7004-ND/810145)
+P3|Male|[952-2262-ND](https://www.digikey.no/product-detail/en/harwin-inc/M20-9990246/952-2262-ND/3728226)
+P4||[609-1047-ND](https://www.digikey.no/product-detail/en/amphenol-fci/54602-910LF/609-1047-ND/1001361)
+Q1|BC337|[BC33725TACT-ND](https://www.digikey.no/product-detail/en/fairchild-on-semiconductor/BC33725TA/BC33725TACT-ND/1532787)
+R1-5,10,11|10K|[CF14JT10K0CT-ND](https://www.digikey.no/product-detail/en/stackpole-electronics-inc/CF14JT10K0/CF14JT10K0CT-ND/1830374)
+R8|100K|[CF14JT100KCT-ND](https://www.digikey.no/product-detail/en/stackpole-electronics-inc/CF14JT100K/CF14JT100KCT-ND/1830399)
+R9|330R|[CF14JT330RCT-ND](https://www.digikey.no/product-detail/en/stackpole-electronics-inc/CF14JT330R/CF14JT330RCT-ND/1830338)
+R12,13|47K|[CF14JT47K0CT-ND](https://www.digikey.no/product-detail/en/stackpole-electronics-inc/CF14JT47K0/CF14JT47K0CT-ND/1830391)
+S1,2||[450-1650-ND](https://www.digikey.no/product-detail/en/te-connectivity-alcoswitch-switches/1825910-6/450-1650-ND/1632536)
+U2|LM1117-3.3|[LM1117IMPX-3.3/NOPBCT-ND](https://www.digikey.no/product-detail/en/texas-instruments/LM1117IMPX-3.3-NOPB/LM1117IMPX-3.3-NOPBCT-ND/3440160)
+U3|LM358|[LM358NGOS-ND](https://www.digikey.no/product-detail/en/on-semiconductor/LM358NG/LM358NGOS-ND/918519)
+
+Note: The ESP8266 is not included here. It can easily be found on ebay etc

Electrical/README.md

@@ -1,45 +1,16 @@
-# Electrical Design
 
-## Explained
-The design is using an opamp as a compined level converter and a schmitt trigger, in order to convert 
-the HAN signal into a 3.3V compatible serial format. As the input levels on the opamp is much higher 
-than our 5V supply, we are rectifying and smoothing the HAN signal to use for a supply here. (VDD)
+# Overview
 
-As a power source, we've used a micro USB connector, providing 5V, just as this is cheap and easy. However,
-no part of the circuit will need any other power than the 3.3V, so any combination of power source and 
-regulator that provides the 3.3V will do.
+Here are links to the different board designs together with a short summary.
 
-The ESP8266 setup is a rather standaraized setup and will allow for programming the ESP directly on the 
-board, if needed. During programming, it might be neccessary to disconnect the incoming HAN.
+## Board 1
 
-### **!!important changes!!**
-> * R8 should not be used
-> * The two unused inputs on the LM358 should be grounded (Pin 5 and 6)
+This project currently contains only one [board design](Board_001). It
 
-## Schematics
-![Schematics](./Schematics.PNG)
+* is based on the ESP8266 chip.
+* is powered by USB.
+* uses a very simple voltage divider to demodulate the M-bus signal.
 
-## PCB
-![PCB](./PCB.PNG)
+### Status
 
-## Componenet list
-Name | Value | Part
------|------|-----
-C1|10uF/25V|[P5148-ND](https://www.digikey.no/product-detail/en/panasonic-electronic-components/ECA-1EM100/P5148-ND/245007)
-C2|100nF|[BC1101CT-ND](https://www.digikey.no/product-detail/en/vishay-bc-components/K104K10X7RF5UH5/BC2665CT-ND/2356879)
-C3|220uF/35V|[1572-1706-ND](https://www.digikey.no/product-detail/en/illinois-capacitor/227CKS035M/1572-1706-ND/5411729)
-D1|1N4148|[1N4148FS-ND](https://www.digikey.no/product-detail/en/fairchild-on-semiconductor/1N4148/1N4148FS-ND/458603)
-P1||[609-4613-1-ND](https://www.digikey.no/product-detail/en/amphenol-fci/10118192-0001LF/609-4613-1-ND/2785378)
-P2|Female|[S7004-ND](https://www.digikey.no/product-detail/en/sullins-connector-solutions/PPTC061LFBN-RC/S7004-ND/810145)
-P3|Male|[952-2262-ND](https://www.digikey.no/product-detail/en/harwin-inc/M20-9990246/952-2262-ND/3728226)
-P4||[609-1047-ND](https://www.digikey.no/product-detail/en/amphenol-fci/54602-910LF/609-1047-ND/1001361)
-Q1|BC337|[BC33725TACT-ND](https://www.digikey.no/product-detail/en/fairchild-on-semiconductor/BC33725TA/BC33725TACT-ND/1532787)
-R1-5,10,11|10K|[CF14JT10K0CT-ND](https://www.digikey.no/product-detail/en/stackpole-electronics-inc/CF14JT10K0/CF14JT10K0CT-ND/1830374)
-R8|100K|[CF14JT100KCT-ND](https://www.digikey.no/product-detail/en/stackpole-electronics-inc/CF14JT100K/CF14JT100KCT-ND/1830399)
-R9|330R|[CF14JT330RCT-ND](https://www.digikey.no/product-detail/en/stackpole-electronics-inc/CF14JT330R/CF14JT330RCT-ND/1830338)
-R12,13|47K|[CF14JT47K0CT-ND](https://www.digikey.no/product-detail/en/stackpole-electronics-inc/CF14JT47K0/CF14JT47K0CT-ND/1830391)
-S1,2||[450-1650-ND](https://www.digikey.no/product-detail/en/te-connectivity-alcoswitch-switches/1825910-6/450-1650-ND/1632536)
-U2|LM1117-3.3|[LM1117IMPX-3.3/NOPBCT-ND](https://www.digikey.no/product-detail/en/texas-instruments/LM1117IMPX-3.3-NOPB/LM1117IMPX-3.3-NOPBCT-ND/3440160)
-U3|LM358|[LM358NGOS-ND](https://www.digikey.no/product-detail/en/on-semiconductor/LM358NG/LM358NGOS-ND/918519)
-
-Note: The ESP8266 is not included here. It can easily be found on ebay etc
+Prototypes have been made and some people have started using them(?).

README.md

@@ -14,14 +14,14 @@ Components will be ESP8622, Arduino code, a (very simplified) M-bus <-> 3.3V ser
 As a start, we should try to get information from the three types of AMS meters currently being installed in Norway. Some details about these are available here: [NVE_Info_kunder_HANgrensesnitt.pdf](Documentation/NVE_Info_kunder_HANgrensesnitt.pdf)
 
 The project should include:
-- [x] [Simple circuit to transform MBus levels to 3.3V serial](/Electrical)
+- [x] [Simple circuit to transform MBus levels to 3.3V serial](/Electrical/Board_001)
 - [x] [Code to capture and analyze data from PC](/Code/HanDebugger)
 - [x] [Code to capture and analyze data from Arduino](/Code/ESPDebugger)
 - [x] [Sample data from various meters](/Samples)
 - [x] [Documentation on HAN / MBus / DLMS/COSEM](/Documentation)
 - [X] [Code to parse DLMS data into a structure](/Code/Arduino/HanReader/src)
-- [X] [Real schematics, including ESP8266](/Electrical/PCB)
-- [X] [PCB layout](/Electrical/PCB)
+- [X] [Real schematics, including ESP8266](/Electrical/Board_001/PCB)
+- [X] [PCB layout](/Electrical/Board_001/PCB)
 - [ ] Arduino library
 - [X] [Arduino sample sketch to read values and report to MQTT server](/Code/Arduino)
 
@@ -31,7 +31,7 @@ The project should include:
 
 
 ### Circuit prototype
-![Breadboard](/Electrical/Prototype.jpg)
+![Breadboard](/Electrical/Board_001/Prototype.jpg)
 
 ### MQTT output
-![MQTT screenshot](/Electrical/MQTT%20screenshot.png)
+![MQTT screenshot](/Electrical/Board_001/MQTT%20screenshot.png)