mirror of
https://github.com/antonblanchard/microwatt.git
synced 2026-01-13 15:18:09 +00:00
0fb207be60
This implements a cache in fetch1, where each entry stores the address of a simple branch instruction (b or bc) and the target of the branch. When fetching sequentially, if the address being fetched matches the cache entry, then fetching will be redirected to the branch target. The cache has 1024 entries and is direct-mapped, i.e. indexed by bits 11..2 of the NIA. The bus from execute1 now carries information about taken and not-taken simple branches, which fetch1 uses to update the cache. The cache entry is updated for both taken and not-taken branches, with the valid bit being set if the branch was taken and cleared if the branch was not taken. If fetching is redirected to the branch target then that goes down the pipe as a predicted-taken branch, and decode1 does not do any static branch prediction. If fetching is not redirected, then the next instruction goes down the pipe as normal and decode1 does its static branch prediction. In order to make timing, the lookup of the cache is pipelined, so on each cycle the cache entry for the current NIA + 8 is read. This means that after a redirect (from decode1 or execute1), only the third and subsequent sequentially-fetched instructions will be able to be predicted. This improves the coremark value on the Arty A7-100 from about 180 to about 190 (more than 5%). The BTC is optional. Builds for the Artix 7 35-T part have it off by default because the extra ~1420 LUTs it takes mean that the design doesn't fit on the Arty A7-35 board. Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Microwatt
A tiny Open POWER ISA softcore written in VHDL 2008. It aims to be simple and easy to understand.
Simulation using ghdl
You can try out Microwatt/Micropython without hardware by using the ghdl simulator. If you want to build directly for a hardware target board, see below.
- Build micropython. If you aren't building on a ppc64le box you will need a cross compiler. If it isn't available on your distro grab the powerpc64le-power8 toolchain from https://toolchains.bootlin.com. You may need to set the CROSS_COMPILE environment variable to the prefix used for your cross compilers. The default is powerpc64le-linux-gnu-.
git clone https://github.com/micropython/micropython.git
cd micropython
cd ports/powerpc
make -j$(nproc)
cd ../../../
A prebuilt micropython image is also available in the micropython/ directory.
-
Microwatt uses ghdl for simulation. Either install this from your distro or build it. Microwatt requires ghdl to be built with the LLVM or gcc backend, which not all distros do (Fedora does, Debian/Ubuntu appears not to). ghdl with the LLVM backend is likely easier to build.
If building ghdl from scratch is too much for you, the microwatt Makefile supports using Docker or Podman.
-
Next build microwatt:
git clone https://github.com/antonblanchard/microwatt
cd microwatt
make
To build using Docker:
make DOCKER=1
and to build using Podman:
make PODMAN=1
- Link in the micropython image:
ln -s ../micropython/ports/powerpc/build/firmware.bin main_ram.bin
Or if you were using the pre-built image:
ln -s micropython/firmware.bin main_ram.bin
- Now run microwatt, sending debug output to /dev/null:
./core_tb > /dev/null
Synthesis on Xilinx FPGAs using Vivado
-
Install Vivado (I'm using the free 2019.1 webpack edition).
-
Setup Vivado paths:
source /opt/Xilinx/Vivado/2019.1/settings64.sh
- Install FuseSoC:
pip3 install --user -U fusesoc
Fedora users can get FuseSoC package via
sudo dnf copr enable sharkcz/danny
sudo dnf install fusesoc
- Create a working directory and point FuseSoC at microwatt:
mkdir microwatt-fusesoc
cd microwatt-fusesoc
fusesoc library add microwatt /path/to/microwatt/
- Build using FuseSoC. For hello world (Replace nexys_video with your FPGA board such as --target=arty_a7-100):
fusesoc run --target=nexys_video microwatt --memory_size=16384 --ram_init_file=/path/to/microwatt/fpga/hello_world.hex
You should then be able to see output via the serial port of the board (/dev/ttyUSB1, 115200 for example assuming standard clock speeds). There is a know bug where initial output may not be sent - try the reset (not programming button) on your board if you don't see anything.
- To build micropython (currently requires 1MB of BRAM eg an Artix-7 A200):
fusesoc run --target=nexys_video microwatt
Testing
- A simple test suite containing random execution test cases and a couple of micropython test cases can be run with:
make -j$(nproc) check
Issues
This is functional, but very simple. We still have quite a lot to do:
- There are a few instructions still to be implemented
- Need to add caches and bypassing (in progress)
- Need to add supervisor state (in progress)